alcatel_aos¶
Warning
This is automatically generated. In case of any issues, please refer to the source code or, even better, open an issue on the GitHub repository. Thanks! 🤗📖
Commands¶
enable¶
Output: None
Help: enter enable mode
Prompt: - alcatel_aos>
ex¶
Output: None
Help: exit the terminal
Prompt: - alcatel_aos> - alcatel_aos#
show vlan¶
Output:
stree mble src
vlan type admin oper 1x1 flat auth ip tag lrn name
-----+-----+------+------+------+------+----+-----+-----+------+----------
1 std on on on on off off off on VLAN 1
10 std on off on on off off off on name with spaces
100 std on on on on off on off on name-with-dashes
1000 gvrp on on on on off on off on namewithoutnothing
Help: execute the command "show vlan"
Prompt: - alcatel_aos> - alcatel_aos#
show chassis¶
Output:
Chassis 1
Model Name: OS6350-P24,
Description: Chassis,
Part Number: 000000-00,
Hardware Revision: 01,
Serial Number: AAA000000000,
Manufacture Date: JAN 1 2000,
Admin Status: POWER ON,
Operational Status: UP,
Number Of Resets: 1
MAC Address: 00:00:00:00:00:00,
Chassis 2
Model Name: OS6350-P24,
Description: 6350 24 PORT COPPER GE POE ,
Part Number: 000000-00,
Hardware Revision: 01,
Serial Number: AAA000000000,
Manufacture Date: JAN 1 2000,
Admin Status: POWER ON,
Operational Status: UP,
MAC Address: 00:00:00:00:00:00,
Help: execute the command "show chassis"
Prompt: - alcatel_aos> - alcatel_aos#
show interfaces alias¶
Output:
Chas/
Slot/ Admin Link WTR WTS Alias
Port Status Status (sec) (msec)
--------+----------+---------+----------+----------+-----------------------
1/1/1 enable up 0 0 "This is an example"
2/1/10 enable down 0 0 "This_is_an_example"
2/1/11 enable down 0 0 "This"
Help: execute the command "show interfaces alias"
Prompt: - alcatel_aos> - alcatel_aos#
show interfaces ethernet¶
Output:
Slot/Port 1/1 :
Operational Status : up, ""
Last Time Link Changed : MON JAN 08 20:38:47 ,
Number of Status Change: 2,
Type : Ethernet,
SFP/SFP+/XFP : Not Present,
MAC address : aa:aa:aa:aa:aa:aa,
BandWidth (Megabits) : 1000, Duplex : Full,
Autonegotiation : 1 [ 1000-F 100-F 100-H 10-F 10-H ],
Long Frame Size(Bytes) : 9216,
Rx :
Bytes Received : 28902644070, Unicast Frames : 62119123,
Broadcast Frames: 123797, M-cast Frames : 358499,
UnderSize Frames: 0, OverSize Frames: 0,
Lost Frames : 0, Error Frames : 0,
CRC Error Frames: 0, Alignments Err : 0,
Tx :
Bytes Xmitted : 274375376582, Unicast Frames : 97599952,
Broadcast Frames: 1746630116, M-cast Frames : 87217616,
UnderSize Frames: 0, OverSize Frames: 0,
Lost Frames : 0, Collided Frames: 0,
Error Frames : 0
Slot/Port 1/2 :
Operational Status : down, "Admin-Down"
Last Time Link Changed : WED JAN 10 10:00:26 ,
Number of Status Change: 2,
Type : Ethernet,
SFP/SFP+/XFP : GBIC_LX,
MAC address : bb:bb:bb:bb:bb:bb,
BandWidth (Megabits) : - , Duplex : -,
Autonegotiation : 1 [ 1000-F ],
Long Frame Size(Bytes) : 9216,
Rx :
Bytes Received : 1602614019301, Unicast Frames : 1423093884,
Broadcast Frames: 131096783, M-cast Frames : 9298965,
UnderSize Frames: 0, OverSize Frames: 0,
Lost Frames : 0, Error Frames : 0,
CRC Error Frames: 0, Alignments Err : 0,
Tx :
Bytes Xmitted : 313945899784, Unicast Frames : 702405038,
Broadcast Frames: 94040, M-cast Frames : 3193107,
UnderSize Frames: 0, OverSize Frames: 0,
Lost Frames : 0, Collided Frames: 0,
Error Frames : 0
Help: execute the command "show interfaces ethernet"
Prompt: - alcatel_aos> - alcatel_aos#
show interfaces port¶
Output:
Legends: WTR - Wait To Restore
# - WTR Timer is Running & Port is in wait-to-restore state
* - Permanent Shutdown
Slot/ Admin Link Violations Recovery Recovery WTR Alias
Port Status Status Time Max (sec)
------+----------+---------+----------+----------+----------+----------+-----------------------------------------
*1/1 enable up none 300 10 0 "Hello"
1/2 enable down none 300 10 0 ""
1/11 enable down none 300 10 # 10 ""
1/17 disable down none 300 10 0 ""
1/23 disable down none 300 10 0 ""
1/25 enable up none 300 10 0 ""
1/26 enable down none 300 10 0 ""
1/28 enable down none 0 0 0 ""
Help: execute the command "show interfaces port"
Prompt: - alcatel_aos> - alcatel_aos#
show interfaces status¶
Output:
DETECTED CONFIGURED
Slot/ AutoNego Speed Duplex Hybrid Speed Duplex Hybrid Trap
Port (Mbps) Type (Mbps) Mode LinkUpDown
-----+--------+------+------+------+--------+------+------+------
1/1 Enable 1000 Full NA Auto Auto NA -
1/2 Enable - - - Auto Auto NA -
1/3 Enable - - - Auto Auto NA -
1/4 Enable - - - Auto Auto NA -
1/5 Enable - - - Auto Auto NA -
1/6 Enable - - - Auto Auto NA -
1/7 Enable - - - Auto Auto NA -
1/8 Enable - - - Auto Auto NA -
1/9 Enable - - - Auto Auto NA -
1/10 Enable - - - Auto Auto NA -
1/11 Enable - - - Auto Auto NA -
1/12 Enable - - - Auto Auto NA -
1/13 Enable - - - Auto Auto NA -
1/14 Enable - - - Auto Auto NA -
1/15 Enable - - - Auto Auto NA -
1/16 Enable - - - Auto Auto NA -
1/17 Enable - - - Auto Auto NA -
1/18 Enable - - - Auto Auto NA -
1/19 Enable - - - Auto Auto NA -
1/20 Enable - - - Auto Auto NA -
1/21 Enable - - - Auto Auto NA -
1/22 Enable - - - Auto Auto NA -
1/23 Enable - - - Auto Auto NA -
1/24 Enable - - - Auto Auto NA -
1/25 Enable 1000 Full NA 1000 Full NA -
1/26 Enable - - - 1000 Full NA -
FF - ForcedFiber PF - PreferredFiber F - Fiber
FC - ForcedCopper PC - PreferredCopper C - Copper
Help: execute the command "show interfaces status"
Prompt: - alcatel_aos> - alcatel_aos#
show linkagg alias¶
Output:
Admin Oper Att/Sel
Number Aggregate Size state state Ports Name
-------+----------+----+------------+-------+---------+--------------
2 Dynamic 2 ENABLED UP 2 2 LINK_LACP_CORE
31 Dynamic 8 ENABLED DOWN 0 0 Created by Auto-Fabric on Mon Oct 6 00:00:00 2000
32 Dynamic 8 ENABLED DOWN 0 0 Created by Auto-Fabric on Mon Oct 01 00:00:00 2000
Help: execute the command "show linkagg alias"
Prompt: - alcatel_aos> - alcatel_aos#
show linkagg port¶
Output:
Slot/Port Aggregate SNMP Id Status Agg Oper Link Prim
---------+---------+-------+----------+----+----+----+----
1/1 Dynamic 1000 ATTACHED 1 UP UP YES
1/2 Dynamic 1001 ATTACHED 1 UP UP NO
1/3 Dynamic 1002 ATTACHED 2 UP UP YES
1/4 Dynamic 1003 ATTACHED 2 UP UP NO
Help: execute the command "show linkagg port"
Prompt: - alcatel_aos> - alcatel_aos#
show lldp remote-system¶
Output:
Remote LLDP Agents on Local Slot/Port 1/1:
Chassis aa:aa:aa:aa:aa:aa, Port bb:bb:bb:bb:bb:bb:
Remote ID = 1,
Chassis Subtype = 1 (MAC Address),
Port Subtype = 1 (MAC address),
Port Description = Alcatel-Lucent Enterprise OAW-AP1201H eth0-4094,
System Name = AP,
System Description = Alcatel-Lucent Enterprise OAW-AP1201H 1.0.0.10,
Capabilities Supported = Bridge WLAN AP Router Station Only,
Capabilities Enabled = Bridge WLAN AP Router,
Management IP Address = 1.1.1.1,
MED Device Type = Network Connectivity,
MED Capabilities = Capabilities | Power via MDI-PD(33),
MED Extension TLVs Present = Network Policy| Inventory,
MED Power Type = PD Device,
MED Power Source = PSE and Local,
MED Power Priority = Low,
MED Power Value = 25.4 W
Remote LLDP Agents on Local Slot/Port 1/2:
Chassis aa:aa:aa:aa:aa:aa, Port bb:bb:bb:bb:bb:bb:
Remote ID = 1,
Chassis Subtype = 1 (MAC Address),
Port Subtype = 1 (MAC address),
Port Description = Alcatel-Lucent Enterprise OAW-AP1321 eth1,
System Name = AP,
System Description = Alcatel-Lucent Enterprise OAW-AP1321 1.0.0.10,
Capabilities Supported = Bridge WLAN AP Router Station Only,
Capabilities Enabled = Bridge WLAN AP Router,
Management IP Address = 1.1.1.1,
MED Device Type = Network Connectivity,
MED Capabilities = Capabilities | Power via MDI-PD(33),
MED Extension TLVs Present = Network Policy| Inventory,
MED Power Type = PD Device,
MED Power Source = PSE and Local,
MED Power Priority = Low,
MED Power Value = 25.4 W,
Remote port MAC/PHY AutoNeg = Supported Enabled Capability 0x8336,
Mau Type = 1000BaseTFD - Four-pair Category 5 UTP full duplex mode
Remote LLDP Agents on Local Slot/Port 1/3:
Chassis aa:aa:aa:aa:aa:aa, Port bb:bb:bb:bb:bb:bb:
Remote ID = 1,
Chassis Subtype = 1 (MAC Address),
Port Subtype = 1 (MAC address),
Port Description = Alcatel-Lucent Enterprise OAW-AP1361 eth0,
System Name = AP,
System Description = Alcatel-Lucent Enterprise OAW-AP1361 1.0.0.10,
Capabilities Supported = Bridge WLAN AP Router Station Only,
Capabilities Enabled = Bridge WLAN AP Router,
Management IP Address = 1.1.1.1,
MED Device Type = Network Connectivity,
MED Capabilities = Capabilities | Power via MDI-PD(33),
MED Extension TLVs Present = Network Policy| Inventory,
Remote port MAC/PHY AutoNeg = Supported Enabled Capability 0x8337,
Mau Type = 1000BaseTFD - Four-pair Category 5 UTP full duplex mode
Remote LLDP Agents on Local Slot/Port 1/4:
Chassis aa:aa:aa:aa:aa:aa, Port 1001:
Remote ID = 123,
Chassis Subtype = 1 (MAC Address),
Port Subtype = 1 (Locally assigned),
Port Description = Alcatel-Lucent OS6860 GNI 1/1/1,
System Name = SW,
System Description = (null),
Capabilities Supported = Bridge Router,
Capabilities Enabled = Bridge Router,
Management IP Address = 1.1.1.1
Remote LLDP Agents on Local Slot/Port 1/24:
Chassis aa:aa:aa:aa:aa:aa, Port GigabitEthernet0/0/47:
Remote ID = 223,
Chassis Subtype = 4 (MAC Address),
Port Subtype = 5 (Interface name),
Port Description = UPLINK,
System Name = super_mega_switch,
System Description = S5700-52P-PWR-LI-AC
Huawei Versatile Routing Platform Software
VRP (R) software, Version 1.110 (S5700 A000A000A00AAA000)
Copyright (C) 2000-2001 HUAWEI TECH Co., Ltd.,
Capabilities Supported = Bridge Router,
Capabilities Enabled = Bridge Router,
Management IP Address = 1.1.1.1
Remote port default vlan = 2000,
Vlan ID = 1,
Vlan Name = VLAN 0001,
Protocol vlan Id = 0 (Flags = 0),
Remote port MAC/PHY AutoNeg = Supported Enabled Capability 0xa03e,
Mau Type = 1000BaseTFD - Four-pair Category 5 UTP full duplex mode
Help: execute the command "show lldp remote-system"
Prompt: - alcatel_aos> - alcatel_aos#
show mac-address-table¶
Output:
Legend: Mac Address: * = address not valid
Vlan Mac Address Type Protocol Operation Interface
------+-------------------+--------------+-----------+------------+-----------
* 1 aa:aa:aa:aa:aa:aa permanent --- bridging 1/1
2 bb:bb:bb:bb:bb:bb learned --- bridging 1/1
3 cc:cc:cc:cc:cc:cc learned --- bridging 1/1
4 dd:dd:dd:dd:dd:dd learned --- bridging 1/1
* 999 ee:ee:ee:ee:ee:ee permanent 0 bridging 1/11
Total number of Valid MAC addresses above = 4
Help: execute the command "show mac-address-table"
Prompt: - alcatel_aos> - alcatel_aos#
show port-security¶
Output:
Legend: Mac Address: * = Duplicate Static
Mac Address: # = Pseudo Static
Port: 1/11
Operation Mode : ENABLED,
Max MAC bridged : 1,
Trap Threshold : DISABLED,
Max MAC filtered : 5,
Violation : RESTRICT,
Violating MAC : NULL
MAC Address VLAN TYPE
-------------------+------+------------
aa:aa:aa:aa:aa:aa 10 STATIC
Legend: Mac Address: * = Duplicate Static
Mac Address: # = Pseudo Static
Port: 1/12
Operation Mode : ENABLED,
Max MAC bridged : 1,
Trap Threshold : DISABLED,
Max MAC filtered : 5,
Violation : RESTRICT,
Violating MAC : NULL
MAC Address VLAN TYPE
-------------------+------+------------
aa:aa:aa:aa:aa:bb 10 STATIC
Help: execute the command "show port-security"
Prompt: - alcatel_aos> - alcatel_aos#
show system¶
Output:
System:
Description: Alcatel-Lucent Enterprise OS6350-P24 6.7.1.001.R01 GA, January 01, 2000.,
Object ID: 0.0.0.0.0.0.0000.000.0.0.0.0.00.0.0,
Up Time: 22 days 2 hours 20 minutes and 20 seconds,
Contact: Alcatel-Lucent Enterprise, https://www.al-enterprise.com,
Name: SWA_0001,
Location: Espoo - Finland,
Services: 2,
Date & Time: MON JAN 01 2001 00:00:00 (CET)
Flash Space:
Primary CMM:
Available (bytes): 39243776,
Comments : None
Help: execute the command "show system"
Prompt: - alcatel_aos> - alcatel_aos#
show vlan port¶
Output:
vlan port type status
--------+------------+------------+--------------
1 1/1/23 default inactive
1 1/1/25 qtagged forwarding
Help: execute the command "show vlan port"
Prompt: - alcatel_aos> - alcatel_aos#