aruba_os¶
Warning
This is automatically generated. In case of any issues, please refer to the source code or, even better, open an issue on the GitHub repository. Thanks! 🤗📖
Commands¶
enable¶
Output: None
Help: enter enable mode
Prompt: - aruba_os>
show arp¶
Output:
Codes: * - Local Addresses, S - Static, A - Auth
Total ARP entries: 2
IPV4 ARP Table
--------------
Protocol IP Address Hardware Address Interface Age (min)
---------- ---------- ---------------- --------- ---------
Internet 10.13.68.113 24:be:05:28:10:71 vlan10 78
Internet 10.13.68.114 b0:5a:da:38:7e:0d vlan10 19
Internet 10.13.68.117 10:e7:c6:05:d3:22 vlan10 62
Internet 10.13.68.118 9c:eb:e8:75:0d:89 vlan10 1376
Internet 10.13.68.119 70:5a:0f:d8:fc:cc vlan10 65
Internet 10.13.68.120 10:e7:c6:6e:6a:d2 vlan10 25
Internet 10.13.68.121 80:ce:62:5e:c4:d1 vlan10 63
Internet 10.13.68.123 10:e7:c6:6e:3a:fe vlan10 12
Internet 10.13.68.124 50:65:f3:1b:53:67 vlan10 46
Internet 10.13.68.126 78:ac:c0:82:83:9c vlan10 1376
Internet 10.13.68.128 d4:95:24:ee:bd:d6 vlan10 1353
Internet 10.13.68.150 78:f2:9e:90:f1:72 vlan10 1376
Help: execute the command "show arp"
Prompt: - aruba_os> - aruba_os#
show ap database long¶
Output:
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP Wired MAC Address Serial # Port FQLN Outer IP User
---- ----- ------- ---------- ------ ----- --------- ---------- ----------------- -------- ---- ---- -------- ----
ap-building-1 building 635 192.168.1.1 Up 2d:17h:8m:4s 2Sf 192.168.2.2 192.168.2.3 cc:88:c7:11:22:33 CNM12345 N/A N/A N/A N/A
ap-building-2 building 515 192.168.1.2 Up 2d:17h:8m:23s 2Sf 192.168.2.2 192.168.2.3 cc:88:c7:11:22:34 CNM12346 N/A N/A N/A N/A
ap-building-3 building 505H 192.168.1.3 Up 2d:16h:57m:55s 2Sf 192.168.2.2 192.168.2.3 cc:88:c7:11:22:35 CNM12347 N/A N/A N/A N/A
Flags: 1 = 802.1x authenticated AP use EAP-PEAP; 1+ = 802.1x use EST; 1- = 802.1x use factory cert
2 = Using IKE version 2; 4 = WiFi Uplink
B = Built-in AP; C = Cellular RAP; D = Dirty or no config
E = Regulatory Domain Mismatch; F = AP failed 802.1x authentication
G = No such group; I = Inactive; J = USB cert at AP; L = Unlicensed
M = Mesh node
N = Duplicate name; P = PPPoe AP; R = Remote AP; R- = Remote AP requires Auth
S = Standby-mode AP; T = Thermal ShutDown; U = Unprovisioned; X = Maintenance Mode
Y = Mesh Recovery
b = bypass of AP1x timeout; c = CERT-based RAP; e = Custom EST cert; f = No Spectrum FFT support
i = Indoor; o = Outdoor; l = LAG 802.3ad; m = Protocol Mismatch
p = In deep-sleep status; r = Power Restricted; s = LACP striping; t = Temperature Restricted
u = Custom-Cert RAP; z = Datazone AP
Help: execute the command "show ap database long"
Prompt: - aruba_os> - aruba_os#
show ap database¶
Output:
AP Database
-----------
Name Group AP Type IP Address Status Flags Switch IP Standby IP
---- ----- ------- ---------- ------ ----- --------- ----------
ap-building-1 building 635 192.168.1.1 Up 2d:17h:8m:4s 2Sf 192.168.2.2 192.168.2.3
ap-building-2 building 515 192.168.1.2 Up 2d:17h:8m:23s 2Sf 192.168.2.2 192.168.2.3
ap-building-3 building 505H 192.168.1.3 Up 2d:16h:57m:55s 2Sf 192.168.2.2 192.168.2.3
Flags: 1 = 802.1x authenticated AP use EAP-PEAP; 1+ = 802.1x use EST; 1- = 802.1x use factory cert
2 = Using IKE version 2; 4 = WiFi Uplink
B = Built-in AP; C = Cellular RAP; D = Dirty or no config
E = Regulatory Domain Mismatch; F = AP failed 802.1x authentication
G = No such group; I = Inactive; J = USB cert at AP; L = Unlicensed
M = Mesh node
N = Duplicate name; P = PPPoe AP; R = Remote AP; R- = Remote AP requires Auth
S = Standby-mode AP; T = Thermal ShutDown; U = Unprovisioned; X = Maintenance Mode
Y = Mesh Recovery
b = bypass of AP1x timeout; c = CERT-based RAP; e = Custom EST cert; f = No Spectrum FFT support
i = Indoor; o = Outdoor; l = LAG 802.3ad; m = Protocol Mismatch
p = In deep-sleep status; r = Power Restricted; s = LACP striping; t = Temperature Restricted
u = Custom-Cert RAP; z = Datazone AP
Help: execute the command "show ap database"
Prompt: - aruba_os> - aruba_os#
show ap bss-table details¶
Output:
fm (forward mode): T-Tunnel, S-Split, D-Decrypt Tunnel, B-Bridge (s-standard, p-persistent, b-backup, a-always), n-anyspot
cluster (cluster role): U-UAC, A-AAC, sU-Standby UAC, sA-Standby AAC
Aruba AP BSS Table
------------------
bss ess port ip band/ht-mode/bandwidth ch/EIRP/max-EIRP type cur-cl ap name in-t(s) tot-t mtu acl-state acl fm flags cluster active-clients standby-clients datazone
--- --- ---- -- ---------------------- ---------------- ---- ------ ------- ------- ----- --- --------- --- -- ----- ------- -------------- --------------- --------
aa:bb:cc:dd:ee:ff test1 N/A 192.168.1.2 5GHz/HE/40MHz 136-/19.0/27.1 ap 0 test1-ap 0 11h:0m:35s 1500 - 2 T KrT A 0 0 no
aa:bb:cc:dd:ee:fa test1 N/A 192.168.1.2 2.4GHz/HE/20MHz 6/9.0/26.9 ap 0 test1-ap 0 11h:1m:17s 1500 - 119 T KT A 0 0 no
aa:bb:cc:dd:ee:fb test1 N/A 192.168.1.2 6GHz/HE/160MHz 197S/16.0/24.3 ap 0 test1-ap 0 11h:0m:56s 1500 - 119 T KT A 0 0 no
aa:bb:cc:dd:ee:fc multi word ssid N/A 192.168.1.3 2.4GHz/HE/20MHz 6/9.0/26.9 ap 0 test2-ap 0 11h:0m:57s 1500 - 2 T KrT A 0 0 no
aa:bb:cc:dd:ee:fd test 2 N/A 192.168.1.3 5GHz/HE/40MHz 120-/19.0/28.7 ap 0 test2-ap 0 11h:1m:28s 1500 - 119 T KT A 0 0 no
Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.
fm (forward mode): T-Tunnel, S-Split, D-Decrypt Tunnel, B-Bridge (s-standard, p-persistent, b-backup, a-always), n-anyspot
cluster (cluster role): U-UAC, A-AAC, sU-Standby UAC, sA-Standby AAC
Help: execute the command "show ap bss-table details"
Prompt: - aruba_os> - aruba_os#
show ip interface brief¶
Output:
Interface IP Address / IP Netmask Admin Protocol
vlan 93 162.25.53.4 / 255.255.255.192 up up
vlan 1 unassigned / unassigned up up
vlan 69 162.25.53.9 / 255.255.255.192 up up
vlan 999 162.21.33.196 / 255.255.255.240 up up
loopback unassigned / unassigned up up
Help: execute the command "show ip interface brief"
Prompt: - aruba_os> - aruba_os#
show ap radio-database¶
Output:
AP Radio Database
-----------------
Name Group AP Type IP Address Status Flags Switch IP Standby IP Radio 0 Band/Chan/HT-Type/EIRP Radio 1 Band/Chan/HT-Type/EIRP Radio 2 Band/Chan/HT-Type/EIRP
---- ----- ------- ---------- ------ ----- --------- ---------- ------------------------------ ------------------------------ ------------------------------
ap-building-1 building 635 192.168.1.1 Up 35d:23h:44m:14s 2Sf 192.168.2.2 192.168.2.3 AP:5GHz/132+/HE/20.0 AP:2.4GHz/6/HE/9.0 AP:6GHz/197S/HE/17.0
ap-building-2 building 515 192.168.1.2 Up 35d:23h:44m:12s 2Sf 192.168.2.2 192.168.2.3 AP:5GHz/100+/HE/19.0 AP:2.4GHz/11/HE/9.0 N/A
ap-building-3 building 505H 192.168.1.3 Up 35d:23h:44m:19s 2Sf 192.168.2.2 192.168.2.3 N/A AP:2.4GHz/6/HE/9.0 N/A
Flags: 1 = 802.1x authenticated AP use EAP-PEAP; 1+ = 802.1x use EST; 1- = 802.1x use factory cert
2 = Using IKE version 2; 4 = WiFi Uplink
B = Built-in AP; C = Cellular RAP; D = Dirty or no config
E = Regulatory Domain Mismatch; F = AP failed 802.1x authentication
G = No such group; I = Inactive; J = USB cert at AP; L = Unlicensed
M = Mesh node
N = Duplicate name; P = PPPoe AP; R = Remote AP; R- = Remote AP requires Auth
S = Standby-mode AP; T = Thermal ShutDown; U = Unprovisioned; X = Maintenance Mode
Y = Mesh Recovery
b = bypass of AP1x timeout; c = CERT-based RAP; e = Custom EST cert; f = No Spectrum FFT support
i = Indoor; o = Outdoor; l = LAG 802.3ad; m = Protocol Mismatch
p = In deep-sleep status; r = Power Restricted; s = LACP striping; t = Temperature Restricted
u = Custom-Cert RAP; z = Datazone AP
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.
Help: execute the command "show ap radio-database"
Prompt: - aruba_os> - aruba_os#
show ipv6 interface brief¶
Output:
Interface [Status/Protocol]
vlan 1 [ up/up ]
fe80::1a:3e00:6ed1:1585/64
2001::1/64
vlan 390 [ up/up ]
unassigned
vlan 991 [ up/up ]
fe80::1a:3e00:6ed1:1585/64
2a01:9e73:433f:109::6/64
vlan 992 [ up/up ]
unassigned
loopback [ up/up ]
fe80::1a:3e00:6ed1:1585/64
Help: execute the command "show ipv6 interface brief"
Prompt: - aruba_os> - aruba_os#
show hostname¶
Output:
Hostname is WLC-AMC72-LAB01
Help: execute the command "show hostname"
Prompt: - aruba_os> - aruba_os#
show inventory¶
Output:
Supervisor Card slot : 0
System Serial# : CV123ABC2 (Date:08/25/18)
CPU Card Serial# : ABC123XYZ (Date:08/25/18)
CPU Card Assembly# : 2010151H
CPU Card Revision : (Rev:11.00)
Interface Card Serial# : AI3ABC12379 (Date:08/25/18)
Interface Card Assembly# : 2010085E
Interface Card Revision : (Rev:04.00)
SC Model# : Aruba7210-US
HW MAC Addr : 00:1a:1e:05:27:60 to 00:1a:1e:05:27:67
CPLD Version : (Rev: 3.0)
Power Supply 0 : Present : No
Power Supply 1 : Present : Yes
: 12V OK : Yes
: Fan OK : Yes
: Aruba Model No : 2510057
: Vendor & Model No : QCS DCJ3501-01P
: Serial No : QC1234506L
: MFG Date : 7/2/18
: Output 1 Config : 12V 350W
: Input Min : 90V AC
: Input Max : 264V AC
Main Board Temperatures :
: U24 - Local Temp 25 C (shadow of XLP heatsink)
: Q1 - Remote 1 Temp 27 C (shadow of VRM, VDD_CPU)
: Q2 - Remote 2 Temp 26 C (shadow of VRM, VDD_SOC)
: U44 - Local Temp 20 C (shadow of DPI connector)
: U29 - Remote 1 Temp 24 C (XLP die temperature)
: Q36 - Remote 2 Temp 21 C (shadow of 98X1422)
: J2 - DDR A Temp 18 C (DDR3 A temp)
: J4 - DDR B Temp 22 C (DDR3 B temp)
: J1 - DDR C Temp 19 C (DDR3 C temp)
: J3 - DDR D Temp 20 C (DDR3 D temp)
: Port 0 Temp 23 C (1G PHY temp)
: Port 1 Temp 23 C (1G PHY temp)
Interface Board Temperatures :
: U21 - Local Temp 23 C (shadow of port 1 RJ45)
: Q4 - Remote 1 Temp 22 C (shadow of 88E1543)
: Q3 - Remote 2 Temp 25 C (shadow of 88X2140)
Fan 0 : 9070 rpm (5.831 V),Speed Low
Fan 1 : 9112 rpm (5.921 V),Speed Low
Fan 2 : 8916 rpm (5.809 V),Speed Low
Fan 3 : 9049 rpm (5.876 V),Speed Low
Main Board Voltages :
ispPAC_POWR1014A_A :
: 1V2 1.20V sense 1.208 V
: VDD SOC 0.943V sense 0.928 V
: VCC IOBD 1V5 1.50V sense 1.538 V
: DDR3BD_VTT 0.75V sense 0.760 V
: VCC 1A 1.00V sense 1.026 V
: IV8_DIGITAL 1.80V sense 1.852 V
: 3V3_MAIN 3.30V sense 3.348 V
: VCC1 1.00V sense 1.024 V
: VCC25 2.50V sense 2.538 V
: 3V3 SB 3.30V sense 3.366 V
ispPAC_POWR1014A_B :
: VDD 0.837V sense 0.850 V
: VCC IOAC 1V5 1.50V sense 1.546 V
: DDR3AC_VTT 0.75V sense 0.760 V
: VDD_SRAM 1.00V sense 1.048 V
: VCC1B 1.00V sense 1.030 V
: 1V8_ANALOG 1.80V sense 1.842 V
: 1V8 1.80V sense 1.848 V
: VDDIO12_XAUI 1.20V sense 1.212 V
: 5V 5.00V sense 5.016 V
Interface Board Voltages :
ispPAC_POWR6AT6 :
: VCC33 3.30V sense 3.342 V
: VCC 18 1.80V sense 1.840 V
: VCC1 1.00V sense 1.024 V
: VCC12 1.20V sense 1.220 V
: VCC12-DVDD 1.20V sense 1.214 V
: VCC9 0.90V sense 0.932 V
Help: execute the command "show inventory"
Prompt: - aruba_os> - aruba_os#
show version¶
Output:
Image stamp: /ws/swbuildm/rel_venice_qaoff/code/build/lvm(swbuildm_rel_venice_qaoff_rel_venice)
Mar 26 2018 23:16:08
WC.16.05.0007
570
Boot Image: Primary
Boot ROM Version: WC.16.01.0005
Active Boot ROM: Primary
Help: execute the command "show version"
Prompt: - aruba_os> - aruba_os#
show vlan¶
Output:
Status and Counters - VLAN Information
Maximum VLANs to support : 128
Primary VLAN : DEFAULT_VLAN
Management VLAN :
VLAN ID Name | Status Voice Jumbo
------- -------------------------------- + ---------- ----- -----
1 DEFAULT_VLAN | Port-based No No
102 Printers | Port-based No No
103 Workstations | Port-based No No
104 Management | Port-based No No
105 AP_Management | Port-based No No
106 WiFi_ot | Port-based No No
107 WiFi_main | Port-based No No
108 WiFi_guest | Port-based No No
Help: execute the command "show vlan"
Prompt: - aruba_os> - aruba_os#